Pressure reducing valve

Hydraulically driven chainsaw The Cutmaster Basichas been specially developed for use in cutting devices and firewood harvesters. The saw can be supplied with various sizes of powerful hydyraulic motors which drive the chain with a cutting speed of 20m/s. Due to the large selection of sword lengths (54cm to113cm) the Cutmaster Basic can be used very variably. The chain is tensioned by a set screw and lubricated by the integrated lubrication system. The Cutmaster Basic is equipped with a hdraulic swivel system.. - Integrated chain lubrication- 20 metres/sec cutting speed- chain pitch 0.404".- chain wheel with 14 dents- left-hand and right-hand design- hydraulic swivel device- swivel axis in the motor shaft- robust stainless steel construction

Grapple saw Cutmaster Basic The grapple saw may be attached to different grippers on excavators, cranes or front loaders. For this purpose, three different sizes are available. The saw as well as the lubrication oil tank are mounted in the blade protection which can be attached to your gripper via oblong holes. The size of the sword protection is adjusted to the length of your blade. Should you wish to mount a longer sword, this is possible. The blade then protrudes from the front of the protection. The saw is equipped with a powerful 9.3 kW hydraulic motor which drives the chain to a cutting speed of 20.3 metres/s. At full speed the motor requires 31.5 litres of hydraulic oil per minute.   Upon request also available with other engine sizes. 6 KW (21 litres/min)9.3 KW (31.5 litres/min)14.4 KW (50.4 litres/min)Available blade lengths:54cm64cm75cmThe insert length is the sword length - 10cm Scope of Supply: - Cutmaster Basic (with the chosen motor size) - Blade protection adjusted to the chosen blade length - 1 blade - 1 chain

Electrically driven chainsaw The Cutmaster Electronic has been specially developed for use in cut-to-length devices and automatic splitting machines. The saw is available with powerful electric motors from German manufacturers in various sizes, which drive the chain at a cutting speed of 20 m / s. The chain is tensioned by a set screw and lubricated by the integrated lubrication system. The Cutmaster Elektro is equipped with a hydraulic swivel system. - Integrated chain lubrication- 20 m/sec cutting speed- chain pitch 0.404".- AC motors made by German manufacturers- Chainwheel with 16 dents- By means of frequency converters you can increase the speed- Hydraulic swivel device- Swivel axis in the motor shaft- Robust design

Hydraulically driven chainsaw The Cutmaster Speed has been specially developed for use in cutting devices and firewood harvesters. The saw can be supplied with a powerful Parker axial piston motor, two sizes of which are available. This motor drives the chain with a cutting speed of up to 60 metres/s. Motor size 6ccm: 50 KW – 67 litres/min (at 400bar) Motor size 10ccm: 85 KW – 110 litres/min (at 400bar) While the motors do not have to be driven with a 400 bar pump, please bear in mind that in case of a 200 bar pump, only half the capacity can be reached while the speed remains unchanged. Due to the large selection of sword lengths (54cm to 135cm), the Cutmaster Speed can be used very variably. The chain is tensioned by a set screw and lubricated by the integrated lubrication system. The Cutmaster Speed is equipped with a hdraulic swivel system. - Integrated chain lubrication- 40 metres/sec cutting speed- chain pitch 0.404".- chain wheel with 13 dents- left-hand and right-hand design- hyraulic swivel device- swivel axis in the motor shaft- robust stainless steel construction - Axial piston motor with 10,000 rpm - loadable up to 400bar

Grapple saw Cutmaster Speed The grapple saw may be attached to different grippers on excavators, cranes or front loaders. For this purpose, three different sizes are available. The saw as well as the lubrication oil tank are mounted in the sword protection which can be attached to your gripper via oblong holes. The size of the sword protection is adjusted to the length of your blade. Should you wish to mount a longer sword, this is possible. The blade then protrudes from the front of the protection. The saw can be supplied with a powerful Parker axial piston motor, two sizes of which are available. This motor drives the chain with a cutting speed of up to 60 m/s.   Size of motor 6ccm: 50 KW – 67 litres/min (at 400bar) While the motors do not have to be driven with a 400 bar pump, please bear in mind that in case of a 200 bar pump, only half the capacity can be reached while the speed remains unchanged. Available sword lengths:54cm64cm75cmThe insert length is the sword length -10cm   Scope of supply: - Cutmaster Speed (with the chosen motor size) - Blade protection suitable for the chosen blade length - 1 blade - 1 chain